1、木箱包裝箱體表面不允許有任何損壞和污跡，無銹斑、剝層、龜裂和其它紙材缺陷，箱體里紙面紙不允許有拼接、缺材、露楞、折皺、透膠、色差等感官缺陷，同一批產品面紙白度、紙材必須一致，預印和膠印UV包裝箱面紙上UV層允許有輕微裂痕，不允許有掉渣現象。
1. No damage, stain, rust, peeling, cracking and other paper defects are allowed on the surface of wooden packing box. The paper surface in the box is not allowed to have sensory defects such as splicing, lack of material, exposed ridge, wrinkle, glue penetration and color difference. The whiteness and paper materials of the same batch of products must be consistent. The UV layer on the preprint and offset UV packing box surface paper is allowed to have slight cracks and no residue Phenomenon.
2、包裝箱箱體印刷圖案，文字清晰正確，深淺一致，放置準確（套印誤差范圍為±1mm）,印刷墨跡不允許出現掉墨現象，無錯字、錯印、漏印、重印多余的印刷圖案及字跡，每箱1mm×1mm大小之內漏白現象不得多于5處，如有多余印刷墨跡現象，在箱體正面每箱1mm×1mm大小之內不得多于5處，在箱體側面每箱2mm×2mm大小之內不得多于5處，條碼必須可識別。
2. The printing pattern of the packing box is clear and correct, the depth is consistent, and the placement is accurate (the overprint error range is ± 1 mm), Ink drop is not allowed in printing ink. There are no wrong words, wrong printing, missing printing, and reprint of redundant printing patterns and handwriting. There shall be no more than 5 white spots within the size of 1 mm × 1 mm in each box. If there is redundant printing ink, there shall be no more than 5 white spots within the size of 1 mm × 1 mm in each box on the front of the box and no more than 5 white spots within the size of 2 mm × 2 mm in each box on the side of the box. The barcode must be recognizable.
3、木箱包裝的制作要求應符合標準，GB/T 12464 普通木箱包裝標準規定，木材的含水率一般不大于20%，但外箱檔與B型箱的木材的含水率可在24%以下，木構件的寬度與厚度尺寸不大于20 mm時，其偏差為-1 mm～+2 mm;大于20 mm時，其偏差為±2 mm。
3. The production requirements of wooden box packaging should comply with the national standard, GB / T 12464 standard for ordinary wooden box packaging, the moisture content of wood is generally not more than 20%, but the moisture content of outer box and b-box can be less than 24%, when the width and thickness of wood members are not more than 20 mm, the deviation is - 1 mm to + 2 mm; when it is more than 20 mm, the deviation is ± 2 mm.
4、木箱包裝箱體壓痕線寬度不得大于12mm，折線居中，不得有裂破、斷線、重線等多余的壓痕線及影響感官折跡缺陷。
4. The width of the indentation line of the wooden packing box shall not be greater than 12mm, the folding line shall be in the middle, and there shall be no cracks, broken lines, heavy lines and other redundant indentation lines and defects affecting the sensory.
5、木箱包裝箱體粘合劑為玉米淀粉膠，膠液應涂布均勻，充分，無溢出。粘合必須整齊、牢固、兩片接頭對齊，上下左右錯位不得大于2mm，無箱體與箱體互貼等現象。
5. The adhesive for wooden packing box is corn starch glue. The glue liquid should be coated evenly and fully without overflow. The bonding must be neat and firm, the two pieces of joints must be aligned, and the dislocation of the top, bottom, left and right must not be greater than 2mm, and there is no such phenomenon as the box and the box sticking to each other.
This article is provided by heavy duty carton manufacturers. Our website is: http://www.cdhpd.com We will serve you wholeheartedly and warmly. Welcome to visit!
